Barco Automobile Accessories 26 0904004 00 User Manual

Phone:  
Fax:  
Technical Support:  
Websites:  
+1 (916) 859-2500  
+1 (916) 859-2515  
+1 (866) 374-7878  
EMEA Support  
Barco Events USA  
11101 Trade Center Drive  
Rancho Cordova, CA  
95670 • USA  
Website:  
Phone:  
0800900410  
Quick Start Guide  
Visibly yours  
S3D/Dual  
DisplayPort  
Input  
Connect to  
DisplayPort  
sources.  
Ethernet  
Connect to Web  
Interface or  
Composite  
Output  
Connect to NTSC/  
PAL composite  
video display.  
DVI-I Input with  
Loop-through  
Connect to DVI  
sources.  
Channel Options  
Connect to S3D and  
dual channel sources,  
invert sync signals.  
Audio I/O  
Connect to audio  
source.  
DVI-D Output  
Connect to DVI  
video display.  
external controller.  
Analog  
Output  
Analog Input  
with Loop-  
through  
Connect to  
HD-15 sources.  
AC  
Connect to AC  
power source.  
HDMI  
SDI Input  
with Loop-  
through  
Connect to  
SD-SDI or HD-  
SDI sources.  
SDI  
DisplayPort  
Genlock  
HDMI  
Output  
Connect to  
Input  
Connect to  
HDMI  
Output  
Connect to  
SDI display.  
Output  
Connect to  
DisplayPort  
display.  
Connect a  
reference signal  
such as black  
burst or  
Connect to  
analog  
HDMI display.  
display.  
sources.  
composite sync.  
Setting Up Outputs  
Setting up an LED Display  
Quick Install and Setup  
6. Obtain the output format — If the primary  
output is connected to an HDMI, DVI-D,  
HD-15 or DisplayPort connector, obtain the  
output’s preferred resolution and frame rate  
using the Output Menu. This is the format the  
ImagePRO-II uses. (Chapter 4, “Using EDID  
Auto Config” section)  
10. Position and adjust the image — Use the LED Setup Menu to  
position the image on the LED wall or other display device, scale  
the image, adjust pan and zoom settings, and save your view.  
(Chapter 4, “Positioning an Image on the Display” section.)  
Getting Started  
1. Connect power — Ensure that power is  
properly connected to the ImagePRO-II.  
2. Connect inputs — Connect all input sources to  
Setting Up Inputs  
the ImagePRO-II.  
11.Set and adjust inputs — Select inputs and make any necessary  
adjustments to color balance, timings, and so on. (Chapter 4,  
“Configuring Inputs” section.)  
3. Connect outputs — Connect the output(s) on  
the ImagePRO-II to your projector(s) or other  
target devices.  
7. Adjust output format — If the primary output  
is connected to the composite video connector  
or one the SDI connectors, you can adjust the  
output format manually if necessary. (Chapter  
4, “Setting Output Format” section)  
12.Save input configuration — After adjusting an input, save the  
input configuration. (Chapter 4, “Saving an Input Configuration”  
section.)  
4. Turn on power — Turn on power to the  
ImagePRO-II, your projector(s), and to all  
peripheral equipment.  
8. Test output — Turn on a test pattern, verify  
that you have an image, and make any  
necessary adjustments. When complete, turn  
off the test pattern. (Chapter 4, “Working with  
Test Patterns” section)  
13.Adjust and save system settings — Adjust system parameters  
such as VFD brightness, Ethernet settings, and HDCP  
5. Factory reset — If you are using the  
ImagePRO-II for the first time, or if you are using  
an ImagePRO-II that has just returned from an  
event, perform a full factory reset to restore  
default system configurations.  
parameters. (Chapter 4, “Using the System Menu” section.)  
9. Save output configuration — After  
completing output adjustments, save the  
output configuration.  
ImagePRO-II User’s Guide  
For complete details on all installation and operations procedures,  
please refer to the ImagePRO-II User’s Guide.  
PN 26-0904004-00 Rev 01  
 

2Wire Network Router 2701HGV W User Manual
ADC Network Card UTU 701C User Manual
Agilent Technologies Drums 60501B User Manual
American Standard Hot Tub 2425XXXW LHO User Manual
American Standard Plumbing Product 2455 User Manual
AOC Flat Panel Television L19W981 User Manual
Ask Proxima Projector C410 C420 User Manual
Audiovox Automobile Alarm APS 20LAD User Manual
Ayre Acoustics Stereo Amplifier K 5x User Manual
Beko Flat Panel Television 15LB250MID User Manual