Metra Electronics Car Stereo System 99 5719 User Manual

INSTALLATION INSTRUCTIONS FOR PART 99-5719  
INSTALLATION INSTRUCTIONS FOR PART 99-5719  
APPLICATIONS  
FORD TAURUS  
2004 - 2007  
99-5719  
KIT FEATURES  
• ISO & DIN Head Unit Provision w/ Pocket  
• DDIN Head unit provisions  
• Integrated auto climate controls and display  
• Integrated passenger airbag light  
• Painted Scratch Resistant Matte Black  
KIT COMPONENTS  
• A) Radio Housing • B) ISO Brackets • C) ISO Trim Plate • D) Pocket  
• E) DDIN Brackets • F) DDIN Trim Plate • G) In-Car Temp Sensor Housing • H) Harness Extension  
B
E
C
D
A
H
G
F
TOOLS REQUIRED  
• Radio Removal Tool (Metra Part #86-5618) • Phillips Screwdriver  
• Panel Removal Tool • Socket Set • Cutting Tool or File • T10 Torx Screwdirver  
METRA. THE WORLD’S BEST KITS.™  
METRA. THE WORLD’S BEST KITS.™  
1-800-221-0932  
metraonline.com  
1-800-221-0932  
metraonline.com  
 
© COPYRIGHT 2004-2010 METRA ELECTRONICS CORPORATION  
© COPYRIGHT 2004-2010 METRA ELECTRONICS CORPORATION  
99-5719  
99-5719 DASH DISASSEMBLY  
NOTES  
FORD TAURUS 2004- 2007  
Disconnect the negative  
battery terminal to prevent an  
accidental short circuit.  
1
A
Using Metra’s 86-5618, pull  
the factory radio/climate  
control panel from the dash.  
(Fig. A)  
2
Disconnect the audio system  
3
B
connectors, blower motor  
switch connector, vacuum  
hose harness, a/c damper  
door switch connector, and  
potentiometer connector.  
Remove the panel.  
Remove (2) torx-head screws  
securing the mounting clips to  
the sides of the factory  
radio/climate control panel  
and remove the clips. (Fig. B)  
4
5
Mount the clips to the  
Integrated Mounting Kit with  
the same torx-head screws.  
1
 
99-5719 KIT PREPARATION  
99-5719  
FORD TAURUS 2004- 2007  
FORD TAURUS 2004- 2007  
AUDIO WIRING  
Remove the In-Car temp  
2
1
A
Fig. A  
Back  
wall  
sensor housing from the  
back of the factory control  
panel. Insert into the includ-  
ed In-Car temp sensor  
housing and mount the  
assembly under the dash.  
Open the trunk, remove (4) pop-  
clips from the driver’s side trunk  
liner and remove the liner. (see  
Fig. A) ocate the factory tuner on  
the wall of the trunk and discon-  
nect the speaker and antenna plugs  
Inside edge  
of sub-dash  
Back  
wall  
Fig. B  
Fig. A  
Inside edge  
of sub-dash  
(located under  
the rear deck)  
Fig. B  
(it is NOT necessary to remove  
the tuner). (see Fig. B). Plug the  
70-5715 into the unit speaker plug  
and the antenna extension lead into  
the unit antenna plug. Slide the ex-  
tension harness through the space  
in the back seat between the seat  
back and seat bottom. Unclip the  
rocker trim, tuck the extension har-  
ness under the carpet and stretch  
the harness to the back of the dash.  
(Replace the rocker trim when  
completed). Splice the speaker  
leads on the extension harness into  
the rear of the aftermarket head  
unit. Plug the factory wiringhar-  
nesses into the switch connectors  
(previously mounted in step #2)  
and audio connectors on the back  
of the Integrated Mounting Kit.  
Remove the factory rear sup-  
port in the sub-dash. (Fig. A)  
2
Continue to Kit Assembly  
2
7
 
99-5719  
99-5719  
FORD TAURUS 2004- 2007  
FORD TAURUS 2004- 2007  
DDIN/STACKED ISO DIN  
HEAD UNIT PROVISION  
DIN HEAD UNIT PROVISION  
1
Locate the factory wiring har-  
ness in the dash. Metra  
A
......... Continued from Pg.5  
recommends using the prop-  
er mating adapters (included)  
from Metra and AXXESS to  
integrate your new radio.  
Re-connect the negative bat-  
tery terminal and test the unit  
for proper operation.  
Snap the double DIN trim  
plate into the radio housing.  
(Fig. B)  
B
5
Continue to “Audio Wiring”......  
Slide the DIN cage into the  
Radio Housing and secure  
by bending the metal locking  
tabs down. (Fig. A)  
B
2
Snap the pocket into the  
bottom opening of the radio  
housing. (Fig. B)  
3
Slide the aftermarket head  
unit into the cage and se-  
cure. (Fig. B)  
4
Continue to “Audio Wiring”....  
6
3
 
99-5719  
99-5719  
FORD TAURUS 2004- 2007  
FORD TAURUS 2004- 2007  
DDIN/STACKED ISO DIN  
ISO DIN HEAD UNIT PROVISION  
HEAD UNIT PROVISION  
Locate the factory wiring har-  
1
A
Locate the factory wiring har-  
1
A
ness in the dash. Metra  
recommends using the proper  
mating adapters (included)  
from Metra and AXXESS to  
integrate your new radio. Re-  
connect the negative battery  
terminal and test the unit for  
proper operation.  
ness in the dash. Metra  
recommends using the proper  
mating adapters (included)  
from Metra and AXXESS to  
integrate your new radio. Re-  
connect the negative battery  
terminal and test the unit for  
proper operation.  
Mount the ISO Brackets to the  
head unit with the screws sup-  
plied with the unit. (Fig. A)  
2
3
4
5
B
Cut and remove the center  
bar from the radio housing.  
(Fig.A)  
2
Snap the pocket into the bot-  
tom opening of the radio hous-  
ing. (Fig. B)  
Snap the Double DIN brack-  
ets to the inside edge of the  
Double DIN trim plate.  
3
Slide the head unit into the ra-  
dio opening until the side clips  
engage. (Fig. B)  
Slide the Double DIN head  
unit or stacked ISO head units  
into the bracket/radio housing  
assembly and secure the Dou-  
ble DIN head unit or stacked  
ISO head units to the assem-  
bly using the screws supplied  
4
Snap the Trim plate into the  
Radio Housing.  
Continue to “Audio Wiring”....  
Continued on Pg. 6  
with the radio. (Fig. B)  
4
5
 

Lenoxx Electronics CD Player CDR1906 User Manual
Lexmark Network Card SCTNE User Manual
Makita Drill 6304L User Manual
Mattel Doll X7949 0520G1 User Manual
Maytag Stove OL 1246 01 User Manual
Meade Telescope 2080 LX6 User Manual
Melissa Hair Dryer 635 103 User Manual
Melissa Juicer 644 008 User Manual
Middleby Marshall Oven PS536ES User Manual
Midland Radio Two Way Radio GXT800 User Manual